Compatible Parts
Frame
All model levels feature a full carbon frame (both front and rear triangle). There are no carbon layup changes between models, and all models share the same chainstay and seatstay.
Enduro follows S sizing, which is primarily based on reach. Head tube and seat tube angles remain consistent through out the size run.
BB standard is BSA threaded 73mm.
Maximum chainring size is 36t.
Brake Mount
Minimum rear brake rotor diameter is 180mm, this is direct mount post to caliper. No SBC specific parts are used or needed for setup. Maximum rear brake rotor size is 220mm.
Derailleur Hanger
All models use the sandwich hanger that is used on many other current MTBs.
S172600001 | HGR MY18 MTB THRU AXLE DER HANGER |
Fork
Enduro 29 features 170mm front and rear travel. Low fork offset is designed into the frame geometry.
OE fork offset is 42-44mm depending on manufacturer.
Maximum fork travel is 170mm.
Headsets
All bikes use a tapered flush mount headset with 1 1/8” upper bearing and 1 ½” lower headset bearing. All bikes use Campy type bearings and a split crown race.
Rear Shock
205x60mm trunnion-mount rear shocks are used on all sizes.
Please note: suspension on a bicycle is a complete system. Specialized frames are designed in conjunction with the shocks and supporting parts that come factory-installed. While many aftermarket shocks (air or coil) may physically fit on the bike, they may not be compatible with the frame. Always check with the shock manufacturer to confirm compatibility with your specific frame before purchasing and installing a different shock than what was originally supplied with the bike or frame.
Link and Shock Extensions
Rear suspension for the MY20 Enduro is a multi-link design. Elite and Expert models use alloy links and SW models feature carbon upper and lower links and an alloy mid link. Links are interchangeable across models. All links in the service part line have bearings pressed in, allowing for easy replacement.
S194300012 | SHL MY20 ENDURO CARBON UPPER LINK,MTB,AMTN FSR I1,ALY |
S194300013 | SHL MY20 ENDURO CARBON UPPER LINK,MTB,AMTN FSR I1.1,CRB |
S194300010 | SHL MY20 ENDURO CARBON MID LINK,MTB,AMTN FSR I1.1,ALY |
S194300009 | SHL MY20 ENDURO CARBON LOWER LINK,MTB,AMTN FSR I1.1,29,CRB |
S194300008 | SHL MY20 ENDURO CARBON LOWER LINK,MTB,AMTN FSR I1.1,29,ALY |
The shock extension is shared with all model levels and uses the same geo adjust Flip Chips as the SJ:
S196300002 | SHK EXT MY20 ENDURO CARBON SHOCK EXTENSION KIT |
The geometry adjust flips chips are also available as a stand-alone part.
S189900096 | MSC BSHG, FLG, 8MM ID X 15MM OD X 6.5MM W, 304 SST, GEO ADJ (2 PCS) |
All models are assembled with the Flip Chip in the Low BB setting. Switching to the High BB setting will raise the BB by approximately 7mm and steepen the head tube angle by 0.4°.
Hardware and Bearings
There is one bearing kit which contains all the bearings required to rebuild a frame:
S190600004 | BRG MY20 ENDURO CARBON BEARING KIT |
There is one hardware kit that contains all bolts, washers, and spacers for the entire frame assembly.
S194200052 | SUB MY20 ENDURO CARBON BOLT KIT |
A secondary kit is available that includes all the hardware related to installing the shock to the frame.
S194200053 | SUB MY20 ENDURO CARBON SHOCK HARDWARE KIT |
SWAT
The SWAT door used on the Enduro is similar to the SJ in design but not quite the same.
There are two replacement part kits available.
One includes the door, and hardware required to mount a bottle cage to the door.
S199900093 | MSC MY20 ENDURO CARBON SWAT 2.0 DOOR ASSY |
The other includes the latch, and bolts- everything required to secure the new door to the frame.
S199900094 | MSC MY20 ENDURO CARBON SWAT LATCH KIT |
A bulkhead is positioned inside the downtube to prevent SWAT rolls and spare parts from sliding down to the BB, S199900090.
SWAT CC (Conceal Carry tool) comes on SW, Expert, and Elite models. For reference, there are different parts for the different length anchor bolts available to set up the tool based on the riders desired fork steerer tube length.
STEERER TUBE LENGTH | PART # | DESCRIPTION |
145-160mm | S185300016 | TOL MY18 SWAT CC ANCHOR BOLT / CHAIN PIN DRIVER, 55MM |
165-180mm | S185300017 | TOL MY18 SWAT CC ANCHOR BOLT / CHAIN PIN DRIVER, 75MM |
180-195mm | S185300018 | TOL MY18 SWAT CC ANCHOR BOLT / CHAIN PIN DRIVER, 90MM |
195-210mm | S185300019 | TOL MY18 SWAT CC ANCHOR BOLT / CHAIN PIN DRIVER, 105MM |
210-225mm | S185300020 | TOL MY18 SWAT CC ANCHOR BOLT / CHAIN PIN DRIVER, 120MM |
225-240mm | S182500009 | HDS SWAT CC, ANCHOR BOLT / CHAIN PIN DRIVER, 135MM |
Chainguide
A smaller version of the SJ chain guide is used on the Enduro. The OE chain guide accepts a maximum chain ring diameter of 32T.
SJ chain guides may be used for riders wishing to use larger chain rings, all components are shared aside from the mounting bracket.
S181200001 | CHG SBC CHAIN GUIDE ASSY, ISCG 28T – 36T |
Mounting is through molded ISCG05 tabs, allowing for many aftermarket options to be fitted.
Seatposts
Seat post diameter is 34.9mm and seat clamp is 38.6mm.
S2 & S3 sizes come with 150mm dropper seatposts. S4 & S5 come with 170mm.
X-Fusion Manic posts come on Elite and Expert models.
SW models are equipped with RockShox Reverb AXS in 30.9mm diameter. A shim is required to be used with this seatpost, S174900001.
Tire Sizing
All models are equipped with 29x2.6" front and 29x2.3 rear. Maximum tire size front/rear is 29x2.6.